· OWON Technology · Hotel  · 5 min read

Meet OWON at EquipHotel Paris 2026 — Stand P7.3-F099

Visiting EquipHotel Paris (2-5 November 2026)? The stand shows wireless room control, in-room metering and the gateway behind them — bring room count, HVAC type and what is installed today, and we build a device list on the spot.

Meet OWON at EquipHotel Paris 2026 — Stand P7.3-F099

EquipHotel Paris runs 2-5 November 2026 at Paris Expo Porte de Versailles. OWON exhibits on stand P7.3-F099, and the theme on the back wall is the one we work to every day: wireless IoT solutions for hotel rooms — open, reliable and customisable devices for hotel automation.

This is not a catalogue page. It is a short guide to getting something useful out of the visit, whether you are refurbishing one property or specifying a group.

What is actually on the stand

The stand is built around four blocks, and every device on it is powered and running: HVAC control, energy metering, room automation and the IoT gateway behind them.

BlockWhat you can pick up and look at
HVAC controlFan-coil thermostats for the 3-speed units most European properties run, 24 VAC thermostats for the wall, and wi-fi touchscreen units where the guest interface matters. A C-wire adapter is on the stand too, because “there is no spare wire in the wall” is the most common objection we hear.
Radiator roomsZigBee radiator valves for the properties that heat with water rather than forced air — a large share of the Paris stock.
Energy meteringSingle-phase in-room meters for per-room or per-floor metering, and a three-phase meter for the incoming supply or a plant room. Both read over RS485 as well as Wi-Fi, which matters if the data has to land in a BMS rather than a cloud dashboard.
Room automationMulti-sensors for presence and light, door and window contacts, occupancy sensors and split A/C controllers for the rooms where the unit is a wall-mounted split rather than a fan coil.
Gateway and platformThe ZigBee 3.0 gateway that carries up to 200 devices, and the OWON gateway that publishes to MQTT. A screen runs the live platform so you can see what an operator actually sees.

If you have only ten minutes, spend them on the metering table and the gateway. Those two decide whether a room is a smart room or just a room with a remote control.

Bring three things and leave with a device list

Hotel conversations go nowhere when they stay abstract. If you bring these three, we can work through your rooms at the stand:

  1. Room count and room types — how many keys, and whether they differ (standard, suite, accessible).
  2. The HVAC in those rooms — fan-coil unit, split A/C, boiler and radiators, or a mix.
  3. What is installed today — a wired BMS, standalone thermostats, or nothing yet.

With those three answers the rest is arithmetic: which sensor goes in which room, whether metering is per room, per floor or per building, and how many gateways a property of that shape needs.

What actually happens at the stand

  • Devices out of the box — the room hardware physically there, not photographs of it.
  • Placement and wiring questions — where a sensor goes, what a thermostat needs at the wall, how a gateway is powered and connected.
  • Datasheets on the spot — the technical documents for whatever you are looking at.
  • Rough quantities — not a formal quotation, but enough to sanity-check a budget.

If you are at the specification stage rather than the buying stage, that is fine too — most useful conversations at this show start with “we are planning to replace X”.

Three questions worth asking any hotel IoT supplier

Including us. They separate hardware that survives a hotel from hardware that survives a demo:

  1. What happens when the server is unreachable? A room must still heat, cool and light when the network or the cloud is down.
  2. Is there a device-level interface, or only a dashboard? If you can only read data inside the vendor’s own application, your platform is not really yours.
  3. Can third-party devices join the same network? Rooms fill up with equipment from different suppliers over a building’s life.

A fourth question is worth adding, because it is the one that decides how the year after handover goes:

  1. What does a service call look like six months in? Ask how firmware versions are kept consistent across a property, how high-frequency meter data is rate-limited, and which devices are used to trigger automation chains. A hotel rollout can be perfectly specified and still generate calls if those three are left to chance.

We are happy to be asked all four at the stand, and to show the wiring behind the answers.

The parts that decide the energy bill

If your reason for visiting is cost rather than control, three device decisions do most of the work:

Room-level metering comes first. Without it you are allocating a building’s bill by floor area, which nobody can defend when a department disputes it. A single-phase meter per room turns that into a measurement.

Occupancy has to actually sensor the room. A multi-sensor in the ceiling plus a door contact gives presence and a second signal to confirm it; a PIR alone goes quiet the moment a guest sits still with a laptop.

Setback has to reach the HVAC, not the app. The saving only happens when an empty room stops conditioning. That means a thermostat or split A/C controller that accepts an automation command, and a gateway that keeps issuing it when the WAN is down.

None of this is exotic. It is the difference between a pilot that looks good in a dashboard and a property that renews the contract.

If you cannot make it to Paris

Send the three answers above to [email protected] or WhatsApp +86 136 0097 9005 and we will reply with the relevant datasheets and a device list for your property type. If you already know which block you care about, start from the hotel energy management page — it lists the same devices in the same order they appear on the stand.

Practical details

ShowEquipHotel Paris 2026
Dates2-5 November 2026
VenueParis Expo Porte de Versailles, Paris, France
StandP7.3-F099
ExhibitorXiamen OWON Technology Co., Ltd.

See you in Paris.

Frequently Asked Questions

Where is the OWON stand at EquipHotel Paris 2026?

Stand P7.3-F099, EquipHotel Paris, 2-5 November 2026, Paris Expo Porte de Versailles. The exhibitor listing appears under Xiamen OWON Technology Co., Ltd.

What is actually on the stand?

Wireless devices for guest rooms — fan-coil and 24 VAC thermostats, radiator valves, occupancy and door sensors, in-room energy meters, split A/C controllers — plus the ZigBee gateway and the OWON gateway that tie them together, and a screen running the live platform. The hardware is on the stand, not photographs of it.

What should I bring to the stand?

Three things — the number and types of rooms, the HVAC system in those rooms (fan coil, split A/C, boiler or radiator), and what is installed there today. With those we can put a device list together at the stand instead of exchanging emails afterwards.

Is the stand useful if I only operate one property?

Yes. The same hardware serves a 40-room independent hotel and a multi-property group; what changes is the quantity and whether you meter per room, per floor or per building.

I am a system integrator, not a hotelier. Is it worth visiting?

Yes — the devices are supplied with an open interface, so integrators usually come with a platform question rather than a procurement question. Bring the platform you build on and we will go through how the devices fit it.

Can I get datasheets or a quotation if I cannot attend?

Yes. Email [email protected] or message +86 136 0097 9005 with the property type and the system you are replacing, and we will send the relevant datasheets and a device list.

Back to Blog

Related Posts

View All Posts »